Karcher KM 90-60 R Bp Pack Advanced User Manual download pdf (Page 24)

- 10

 Park the sweeper on an even surface.

 Set programme switch to step 1 (driv-

ing). Roller brush is raised.

 Turn main key to "0" and remove it.

 Press emergency-stop button.

 Secure the machine with wheel

chock(s) to prevent it from rolling away.

 Raise slightly the waste containers on

both sides and pull them out.

 Open the fastening screws of the side

panels on both sides.

 Remove side panels.

 Front sealing strip

 Loosen retaining nuts for the front seal-

ing strip (1) slightly (to replace, un-

screw).

 Screw on new sealing strip without fully

tightening the nuts.

 Adjust sealing strip.

 Set the distance between the sealing

strip and the floor so that the bottom

edge trails behind at a distance of be-

tween 10-15 mm.

 Tighten nuts.

 Rubber strip

 If worn, replace.

 Unscrew retaining nuts for the rubber

strip (2).

 Screw on new rubber strip.

 Rear sealing strip

 Set the distance between the sealing

strip and the floor so that the bottom

edge trails behind at a distance of be-

tween 5 and 10 mm.

 If worn, replace.

 Unscrew retaining nuts for rear sealing

strip (3).

 Screw on new sealing strip.

 Side sealing strips

 Slightly loosen retaining nuts for the

side sealing strip (to replace, unscrew).

 Screw on new sealing strip without fully

tightening the nuts.

 To set the floor clearance, insert a

sheet with a thickness of between 1 and

3 mm under the sealing strip.

 Adjust sealing strip.

 Tighten nuts.

 Screw on side panels.

 Push in the waste containers on both

the sides and lock them.

몇 Warning

Wear a dust mask when working around

the dust filter. Observe safety regulations

on the handling of fine particles.

Note: Wait at least 1 minute before remov-

ing the dust filter so that the dust can settle.

 Open the device hood.

1 Screws (2x)

2 Lid with cleaning device

3 Support

4 Dust filter (flat-fold filter)

 Loosen the screws.

 Fold the lid up and secure it by means

of the support.

 Take out the dust filter.

 Check dust filter, clean or replace

 Insert cleaned or new dust filter.

 Close the lid.

 Tighten the screws.

 Check hose at the suction blower for

tightness.

 Turn main key to "0" and remove it.

 Press emergency-stop button.

 Open the device hood.

 Check tension of circular belt of the

side-brush; also check for wear or dam-

age.

 Check tension, wear and damages on

the V-belt of the sweep roller drive.

 Check tension, wear and damages on

the V-belt of the sweep roller drive.

 Tighten the V-belt at the screw if neces-

sary.

 Check tension, wear and damages on

the V-belt of the sweep roller drive.

 Replace defective fuse.

 Pole fuse

Note

A defective pole fuse may only be replaced

by a Kärcher service technician or an au-

thorised expert. If this fuse is defective,

check the usage conditions and the entire

control system.

 Fuse rotating beacon (option)

To replace a fuse, the front panel must be

removed.

 Loosen the front panel screws.

 Remove front panel.

 Replace defective fuse.

Adjusting and replacing sealing strips

Check/replace dust filter

Check suction blower

Checking drive belt

Replacing the fuse

F 1 Main fuse

Battery pole fuse

150 A

F 2 Automotive flat plug fuse

Vacuum pump

3 A

F 5 Automotive flat plug fuse

Beacon light (optional)

Note: This fuse is located

underneath the front panel

on the left hand side

7,5 A

F 1

F 2

24 EN

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 375 376

Comments to this Manuals

No comments